Standard specs.
LOA: | 50′-9″ (15.47 m) |
LWL: | 48′-4″ (14.73 m ) |
BEAM: | 15′-8” (4.78 m) |
BEAM W/L: | 14′-7 3/4 ” (4.08 m ) |
DRAFT: | 4′-9″ (1.45 m) |
DISPL.: | 71,575 LBS – 1,118.35 CU. FT. – 31.95 LT – (32.53 Metric Tons) @ DWL 57″ above Base Line |
FUEL CAPACITY: | 1450 Gallons (5,489 Liters) |
WATER CAPACITY: | 300 Gallons (1,325 Liters) |
HOLDING TANK CAPACITY: | 85 Gallons (322 Liters) |
GRAY WATER TANK CAPACITY: | 85 Gallons (322 Liters) |
Hull Lamination schedule per construction plan Metyx brand multiaxial fabrics for composites and Sisecam brand glass fibers Skin Coat: DSM ATLACK 580 ACT hiTg vinyl ester resin (132° C) General laminating resin: DSM Synolite 0288-L-1 (HiTg resin) Gelcoat: Büfa ISO/NPG spray type; Büfa Marine NPG gelcoat-S
Deck Lamination schedule per construction plan Metyx brand multiaxial fabrics for composites and Sisecam brand glass fibers Skin Coat: DSM ATLACK 580 ACT hiTg vinyl ester resin (132° C) General laminating resin: DSM Synolite 0288-L-1 (HiTg resin) Gelcoat: Büfa ISO/NPG spray type; Büfa Marine NPG gelcoat-S
Core: Gurit, Airex or Diab core
Cabin side (vertical surfaces)
Cabin top and deck ( horizontal surfaces)
Hull (12″ above water line)
Deck/Hull Joint: Between deck and hull flange: Crystic Crestomer 1152 urethane acrylate structural adhesive
Inside of joint: Two (2) layers of mat and woven roving
Mechanical fastening: ¼” (6.35mm) x 20unc on 6″ (15.2 cm) centers where accessible. In areas that cannot be accessed, self-tapping screws are used
Longitudinal Stringers Hull: port and starboard, engine beds, and floor stringers
Deck: per design
Interior Transverse Floors: per design with foam core
Ballast: internal weight approx. 7000LBS (15,400KG) glassed in-place
Exterior Color Hull: Pebble Grey # RAL 7032
Deck: Pure White # RAL 9010
Non-Skid: Pure White # RAL 9010
Boot Top: Signal Black # RAL 9004
Bottom Paint: Black Two (2) coats SeaHawk epoxy barrier coat Three (3) coats SeaHawk AF33 anti-fouling paint
Main engines x 2: John Deere 4045AFM85 M1 160 bhp @ 2300 – 24v start
Transmissions x 2: ZF220 transmission with 3 to 1 reduction gear
Instrument Panel deluxe with instrumentation for oil pressure, water temperature, voltage, revolutions, hour meter and alarms. Fly bridge panels
Engine control levers: Morse model #31001-001 Twin S Control Cables: Morse 33C Supreme length to suit
Propeller Shaft: 2″ (5.08 mm) diameter A22HS stainless steel ( X 2) Propeller Struts: Two (2) “Y” struts to tie into stainless steel rudder shoes. Per PAE design 316 stainless steel DuraMax cutlass bearing
Propeller: 4-blade bronze, 30″ diameter X 00″ pitch ( CM d X CM p) (X 2) counter rotating
Stern Tube: FRP Bearing: rubber cutlass type (X 2) Stuffing box: tides marine
Fuel filters: duplex Racor 500 MA plus engine mounted filters x 2 Fuel Transfer system with one Racor 500 and Walboro 12v pump Fuel gauges at helm dash added magnetic sight guages with electronic sending unit Fuel Manifold Timer switch for 60 minute intervals
Wet Exhaust Groco Sea Strainers. Marine exhaust slim line FRP mufflers x 2
AC generator Onan Marine QD 11.5 kW Wet exhaust with waterlift muffler and gas/water separator
Stabilizer System: Humphree with 0.6 sq.meter fins (6.46sq. Feet) 24vDC electric
Engine cooling system filled with a suitable mixture of coolant/antifreeze to insure coolant does not freeze for winter shipment
Engine Room floors: FRP with nonskid (white)
Engine Room finish: molded FRP engine beds and floors, insulated with Technicon or equivalent fire proof foiled and leaded foam 2″ (51mm) thick. All exposed insulated surfaces lined with perforated anodized aluminum sheets
Engine Room blowers: Delta T Systems Ignition protected 11″ (279.4) DC Axial Fans with .00 static pressure flow rates to 1424 CFM (2419 m3/h) 24VDC – Part No. 500-311242IP (X 3) vents to have moisture eliminating louvers by Livos or equivalent
Bow Thruster: Side Power 24v 13.5 HP bow thruster includes: model #SE210/250TC – 9.8″ (249mm)I.D. tunnel, 2 x #SM896 joy stick control station, #SM897524 automatic main switch/fuse holder, 500 amp fuse
Water Tank One (1) tank totaling 350 gallons (1,325 liters) FRP construction
Fuel Tanks: Two (2) tanks totaling 1450 gallons (5,489liters) FRP construction Inspection plate appropriately positioned for interior access by an average size man. Each internal baffle with a removable panel to allow access to entire interior of both fuel tanks.
Sight gauges provided to monitor fuel level
Tanks air tested to 4LBS (1.5 KG) per square inch
Baffles provided on 24″ (610mm) centers
Fuel pipe and hoses Supply line from tank to supply reservoir is ¾” (19mm) I.D. with Vetus brand fuel hoseand reusable fittings
Fuel lines from supply reservoir to engines are ½” (13mm) I.D. with Vetus brand fuel hose and reusable fittings Fuel lines from supply reservoir to generator are ½” (13mm) I.D. with Vetus brand fuel hose and reusable fittings Vent lines are fuel certified, reinforced hose ¾” (19mm) I.D.
Water hoses Cold water: blue 15MM diameter Whale brand tubing with Whale fittings
Hot water: red 15MM diameter Whale brand tubing with Whale fittings Sea water hoses: Vetus reinforced rubber certified for marine use and provided with double stainless steel clamps below the water line
Fresh water fill to be Vetus hose
Water Heater: Seaward #S1100 (11 gallon) (41.6 liters) for 240V and heat exchanger operation (60HZ) Quick Nautic BXS 45 LT boiler (50HZ)
Thru Hulls: TruDesign composite non-metalic Each thru hull has a clearly visible tag indicating its function
Water Pump: FloJet Quad II demand pump 4.9 GPM-115Vac-45PSI #4300-143A with Groco PST-1
Plumbing Fixtures: Head sinks: VITRA S50 Bowl 480×360 mm. Galley sink: FRANKE BOX BXX-110-68 Stainless Steel 725×450 mm. Head faucets: GROHE Essence Single Handle Faucet S-size Galley faucet: GROHE Minta Single Handle Pull Out Faucet Shower fixtures: GROHE New Tempesta Cosmopolitan 100 Shower Rail Set Thermostatic Control Unit: GROHE GrohFlex Essence Single Function
Bilge Pumps Electric: Rule 3700 GPH heavy duty pump (X2) Ultra Jr. float switches
Manual: Whale Gusher 30 operable from main salon
1 x High water bilge pump 24 volt Rule 3700 gallons (14,006 liters) per hour – mounted in bilge above normal bilge water height including Ultra Jr. pump switch #WPS-01-24/32 and Ultra bilge alarm #WA-201
Toilet and holding tank pump Dometic VacuFlush 509 Vacuum Toilet, white 24V Holding tank: FRP 85 gallons (322 liters) Sealand T24 pump Holding tank fitted with a deck pump out fixture Gray water crossover valve per PAE design
Gray Water Galley sink, head sinks, shower sumps and washing machine drain to 85 gallon (322 liter) sump tank. Each drain has an appropriate water trap to control odors. Sump includes Sealand Tank Watch 4 24V level indicator and a Sealand T24 waste pump fitted with an 24V Ultra Jr. pump switch #PS02-24volt and auto/manual control panel. Black water crossover valve per PAE design “Y”valve installed at gally sink to divert gally drain directly overboard or to holding tank.
Fresh Water wash down spigots at bow, stern, boat deck and engine room
HyproMarine Electric Command Steering #HM5160/RS ECS helm c/w 1″ staright shaft x two (2) H#HM5290/24 ECS power pack 24 vdc x one (1) #H5195/16 16m ECS harness x one (1) #H5195/19 19m ECS harness x one (1) #HC5378 BA200 11TM 2″ bore 11″ stroke steering cylinder x one (1) Buck Algonquin Heavy Duty tiller arms x two (2) #HM1995/NPT 1.4″ st/st lever valve x one (1) #HM2592 Branch tee x two (2) #HM3242/1 1m hose assembly x four (4) Hydraulic lines per Hypro specification
By-Pass valve for emergency tiller steering
Steering Wheel: 18″ (457mm) x 2
Emergency Tiller: attaches to top of starboard rudder post via inspection plate, stows in lazerrette overhead
RUDDERS and Related Components Stainless steel plate (X 2) Rudder Stock: 2″ (50.8mm) A22HS stainless steel Rudder carrier top: Molded FRP with collar bearing x 2 Rubber cutlass bearing at rudder port openings x 2 Rudder stock stuffing box: Tides Marine x 2 Rudder stock tube: FRP x 2
Electrical Panel consisting of the following:
Electrical panel x one (1)
Engine emergency shut off switch and panel with parallel switches
Inverter: Victron Multiplus 120V -3000 Watt – 120 Amp – 24 v Combi Inverter/Charger for US market –
Inverter: Victron Multiplus 230V -3000 Watt – 120 Amp – 24 v Combi Inverter/Charger for EU market –
inverter by-pass switch
Shore power inlet and AC system per PAE design Smart Plug shore power inlet- 120vac 30amp B30ASSY combo kit- includes 30amp inlet (BM30S) and 30amp connector (BF30) – US builds
Smart Plug shore power inlet- 230vac 32amp B32ASSY combo kit- includes 32amp inlet (BM32S) and 32amp connector (BF32) – EU builds
120 volt 60Hz – US builds
220 volt 50Hz – EU builds
Victron 3600 Watt 115/230 V Isolation Transformer – US Builds
Victron 7000 Watt 230 V Isolation Transformer – EU Builds
Interior outlets per drawing
All galley and head outlets GFCI type
Batteries and 24V DC System per PAE design Batteries: Eight(8) 255+ AH (8D) Lifeline batteries for 24vdc house applications as well as engine starting (1020 amp hours)
Each battery secured with stainless steel tie downs
Battery Cable .00 for general battery leads with .0000 for starting and bow thruster Positive lead is red Negative lead is yellow
Electrolytic Control All hardware mounted below waterline grounded into 24V DC ground system Zincs: One(1) 2-½” x 5-¾ ” (6.35 cm x 14.6 cm) zinc plate tied into the 24V DC ground system
Galvanic isolators on ships service and air conditioning shore power connectors ground
AC Generator Installation Electrical panel to accommodate AC ship’s power
Group 31 starting battery w/ ability to parallel to house bank for emergency starting
Galley Refrigerators – Summit #CT663BCSSADA. Stainless steel Refer/Freezer X 1. Summit #FF63BBISSHVADA all refer x 2 Stove: GE Café Series 30″ electric cook top #CP9530SJSS Oven: GE SS 27″ oven 240 volt – PK7000SFSS Microwave: GE Space Saver Microwave Oven #JVM6175SFSS, w/exhaust blower, Non-Convection
Compactor: GE Trash compactor – #UGC1680LSS 15″ – stainless Cabinetry/paneling: Walnut with satin varnish/wall coverings and some painted surfaces
Overhead: individual padded Majilite panels secured in place with Fast Mount system easily removable for service of deck hardware and wiring
Locker interior finish: Formica
Main salon Floors: Teak and Ebony laminate Cabinetry/paneling: Walnut with satin varnish/wall coverings and some painted surfaces Dinette table: Walnut with stainless steel pedestal Overhead: individual padded Majilite panels secured in place with Fast Mount system easily removable for service of deck hardware and wiring Locker interior finish: Formica Cushions with standard vinyl fabric upholstery choices Walnut valances over windows Settee starboard side Free standing chairs on port side with table in between Lift up TV on starboard side behind settee Front loading freezer Whynter CUF-301BK, Black 3.0 Cu.ft. For USA 60 HZ Ugur Deep Freezer UED 3094 DTK White for Europe 50 HZ
Master cabin and Guest cabin Floors: Teak and Ebony laminate Cabinetry/paneling: Walnut with satin varnish/wall coverings and some painted surfaces Overhead: individual padded Majilite panels secured in place with Fast Mount system easily removable for service of deck hardware and wiring Locker interior finish: Formica Foam mattress with memory foam topper Cedar lined hanging lockers Drop down TV above foot of bunk (Master only)
Floors: Teak and Ebony laminate Cabinetry/paneling: Walnut with satin varnish/wall coverings and some painted surfaces Countertop: White Corian or equivalent Mirror with sconces Shower pan fiberglass with molded in nonskid Overhead: molded FRP Locker interior finish: vinyl/Formica Exhaust blower Glass shower door w/ glass partition
Forepeak Painted with gelcoat Drains overboard
Commissary/Laundry area: GE® 24″ 2.4 Cu. Ft. ENERGY STAR® Front Load Washer with Steam GE® 24″ 4.1 Cu.Ft. Front Load Ventless Condenser Electric Dryer with Stainless Steel Basket Shelving on port and starboard sides above actuators Gelcoated FRP finish with Lonseal flooring
Pilot House Floors: Teak and Ebony laminate Cabinetry/paneling: Walnut with satin varnish/wall coverings and some painted surfaces Countertops and dash panels: black formica with stiched leather wrapping Overhead: individual padded Majilite vinyl panels secured in place with 3M industrial Velcro Table: Walnut Locker interior finish: FRP/formica Cushions with vinyl upholstery Chart light: Imtra 24 volt F4 LED Touch Black Finish Walnut louvers on tops of console for ventilation of electronics Chart drawer under settee
Locker doors and drawers All locker doors and drawers to SOUTHCO Pull to Open Square Latch MP-05-212-11 All drawers to be on stainless steel slides
Interior door handles Interior door handles to be HAFELE BLAIRE with HAFELE Privacy Door Locks
Lighting Main overhead lighting: Quick Marine Lighting Bryan V 4W IP66 Mirror Polished 316SS Warm White Bulkhead reading lights : Quick Marine Lighting QB Swivel 4W Chrome Finish Warm White Engine/laz Room DC Lights: SANEL LED lights (4) total
Exterior Overhead Lights: Quick Marine Lighting Sonia 105 mm. 4W IP66 Mirror Polished 316 SS Daylight Courtesy lights: Quick Marine Lighting Gladis 1 Chrome Finish 1.5W IP65 Daylight
Interior Hanging Locker Lights: Quick Marine Lighting Syria Velvet 15 1.5W Aluminum
FinishExterior Courtesy Lights: Quick Marine Lighting Grace 1 Chrome Finish 1,5W IP 65 Daylight
Switch and Outlets: Vimar Idea Classica Chrome Finish
Interior hand rails to be stainless steel
Exterior Finish and Exterior Equipment | Safety Equipment | Cabin Heating And Cooling Systems | Navigational Equipment | Entertainment System
Horizontal surfaces on deck have Gibco #102 diamond pattern non-skid. Nonskid to be #9010 white
Chocks for mooring lines: Transom: stainless steel with built in cleat
Transom sides: stainless steel with built in cleats x 2
Amidships: stainless steel with built in cleats x 2
Bow: stainless steel with built in cleats x 2
Two (2) x 12″ (30.5 cm) stainless steel cleats at bow
Upper and lower rub rails molded from FRP with a stainless steel rub strip. Rub rails integral to hull
Hull windows and Ports: Lewmar #30209900 Stainless steel round ports in forward cabin trunk x 6 and Lewmar 30209900 Stainless steel round in cabin side x 2. Nine (9) total Fixed rectangular hull windows in fwd cabin port and starboard sides and port guest head and cabin with 3/8″ thick tempered glass.
Bow Roller: Double Stainless steel bow roller designed to accommodate a 100 lbs. (45 kg) Ultra anchor on starboard roller and 3 stranded anchor rode on port roller.
100lb. (45kg) ultra anchor with swivel shackle
400 feet (122m) 3/8″ (10mm) ISO4565 chain
Bitter end of chain to be shackled with 3/4″ line to large pad-eye in chain locker
Windlass: Lofrans SX3 1700 W 24vdc windlass to be mounted on a molded FRP base #600084 chain gypsy for 10mm ISO4565 chain. 2 x control panel with foot switches at fore deck.
Deck hatches: Lewmar Flush 3G standard color with proper drainage channels or scupper drains to suit. Foredeck hatch to have optional 2G handles to comply with escape hatch ISO requirements along with a stowable ladder.
Lewmar #60 x 1 on foredeck
Lewmar #20 x 3 in front of pilot house and over owner’s cabin
10″ diameter flush deck hatch for chain locker inspection and wash down TBD
All hatches fitted with screens
Freeing ports: Cockpit x 2 38″ x 5.75″ with spring loaded flaps, 2 x 22″ x 3.75″ at bow without flaps.
Deck drains: 2″ diameter per deck plan
Windshield wiper: Roca parallel sweep RW with long stud BS blade and AS arm x two (2)
Horn: Kahlenberg K380 + Viair Compressor
Lazerette hatch with drains and lockable lift handles
Fly Bridge: FRP settee with cushions and table, helm chairs x 2, steering wheel and engine, thruster and windlass controls, glass venturi, FRP radar arch w/ stainless steel stinger for anchor light and wind instruments. Storage garage behind F/B with double opening doors. (optional Sunbrella “Bimini Top”)
Wheelhouse and salon windows to be .39″ (10 mm) tempered glass
Windows: Sliding saloon and side wheel house windows to be tinted. Wheel house front windows to be clear and fitted with defogging resistant glass with 24v heating elements
Davit: Steelhead ES1000 4 function hydraulic yacht crane, 6-10′ reach, power rotation – 24 volt
Rails: All exterior rails to be 1 1/4″ diameter unless otherwise noted
Salon door: Dutch door FRP construction
Side doors at pilot house: Dutch door FRP construction
FRP boarding door in transom, starboard bulwark aft with blind dogs and Stainles steel gates through rails port and starboard
Stainless steel U rails 1 1/2″ dia.@ swim step x 2
Stainless steel and teak ladder from lower aft deck to boat deck
Swim ladder mounted on swim step to comply with CE requirements
ACR searchlight RCL 100 LED
Deck lockers: 2 x flush deck fender lockers on starboard side deck. 1 x locker at bow for dock line, winch handle and anchor bridle storage.
All US Coast Guard safety gear
1 x Lalizas LifeLink : 20 USD
8 x Lalizas Alpha 150 N Inflatable Life Jackets : 65 USD / Each 6 x Hand Flare : 15,50 USD / Each
2 x Smoke Signal : 37 USD / Each
6 x Parachute Signal : 38 USD / Each
4 x 2kg Dry Powder Extinguisher for Cabins And Saloon : 30 USD / Each 1 x Spray
Horn : 14 USD
Fireboy 1 CG@ for 500QF in engine room
1X Fireboy ES6 – 6 circuit shutdown for 3 engines and 3 blowers
Lalizas Oceano SOLAS Life Raft- 6 Persons, Container Type With Cradle
Pilot house: S10-R-115V-REV-R410a x 2 self contained units
Master stateroom: S10-R-115V-REV-R410a x 1
Guest Stateroom: S8-R-115V-REV-R410a x 1
Saloon + Galley: S13-R-115V-REV-R410a x 2
Laundry: S6-R-115V-REV-R410a x 1
Webasto EVO 55 Air Heating system for Cabins, Pilot house and Saloon
Garmin Chart plotter and Sounder – GPS Map 8616 XSV 16″ screen in Wheelhouse and 8616 non XSV 16 inch on fly bridge
Garmin Radar GMR 4′ open array – 4KW
Garmin Autopilot – Reactor Hydraulic Corepack with Smart Pump controls in WH and FB
Garmin VHF AIS Marine Radio in Wheelhouse and on Flybridge
Garmin AIS 600 Transceiver
Garmin GCTM 12 Camera mounted in engine room
Garmin P 319 Transducer
Fushion MS-UD755 Marine stereo with Blue Tooth connectivity
Fusion SG F88 8.8 inch Coaxial speaker mounted in saloon and aft deck overheads 4 total
28″ LED TV in saloon and owner’s cabin and fwd guest cabin 3 total. Salon TV on lift. Owner’ cabin TV w/ drop down mechanism from overhead. Guest cabin on wall mount.
Fushion MS-UD755 Marine stereo with Blue Tooth connectivity Fusion SG F88 8.8 inch Coaxial speaker mounted in saloon and aft deck overheads 4 total 28″ LED TV in saloon and owner’s cabin and fwd guest cabin 3 total. Salon TV on lift. Owner’ cabin TV w/ drop down mechanism from overhead. Guest cabin on wall mount.
https://www.youtube.com/watch?v=YO6UG9HUXsw
If you are going to the upcoming Fort Lauderdale Boat Show and haven’t been aboard
Container ships carrying two new Nordhavns arrived in Port Everglades this week, one coming from
https://www.youtube.com/watch?v=zEYGnDCOFaI
https://www.youtube.com/watch?v=DwIUY5LCmCc
Search All Yachts
"Eto Mio" is currently the only Hanse 508 - 3 Cabin / 3 head layout for sale in the USA. She is a luxurious, well-appointed, fast cruiser at home on the Chesapeake Bay or beyond. This boat has been outfitted with distance cruising in mind, comfort & safety a priority.
She has been to the Bahamas twice and safely returned to the Chesapeake Bay. This boat does not do the ICW, but the owner never felt concerned and has over 5,000nm on her bottom.
Currently a year plus wait for a new boat in this size from Hanse. Why wait? Set sail for the sunset
Loaded with lots of cruising equipment, generator, air x3, liferaft, ditch bag, chartplotter, radar, full canvas, lots more. Just Reduced 6/20/2024
Ready to Go Only $697,000
Reasonable offers encouraged.
3 Cabin 3 Head Layout
Sleeps 6 in 3 cabins plus 2 dinette berth & 4 more in cockpit
Forward Master cabin with island double berth, storage space and a head with separate shower stall _ Custom Storage underneath
Full galley to port with stove, sinks, drawer frig/freezer, microwave & pantry
Huge dinette area to starboard - table converts to double berth
Full nav station & chart table on
2 aft cabins with double berths, storage space and separate head
Interior furniture in high quality marine plywood, satin varnish
Hanse companionway closing system
Full complement of B&G Instruments
GRP deck with antislip surface, isophthalic gelcoat, colour: Signal White (RAL 9003), 1st layer vinyl ester resin with balsa sandwich core. 1 cockpit locker on port and stb, stern locker port and stb, stowage for running rigging at helm position, anchor locker at bow.
Scrubbed Grey Synthetic Teak on cockpit seating & sole, plus swim platform
6 Fixed hull windows (3 each side)
GRP hull, isophthalic gelcoat, color: Signal White (RAL9003), 1st layer vinyl ester resin and balsa sandwich laminate
Waterline and cove line, isophthalic gelcoat, color: Dark Grey (RAL 7043)
Twin GRP Wheels White steering system with emergency tiller
2 cockpit tables, stainless steel with teak tops
Bow & Stern Pulpits
Stanchions w/ Gates & SS Wire
Covered halyards and control lines lead to cockpit helm position, organizers and jammers, 4 retractable mooring cleats, handrail on coach roof, bow anchor fitting with teak step
Bathing platform, manual fold-out with swimming ladder
Anchor and forestay fitting
Self tacking jib system
Mainsheet system
8 large and 4 small deck hatches - openable, anchor locker hatch, stowage on coach roof with acrylic glass hatch
6 deck coach roof windows - acrylic glass with portlights next to companionway, portlights in cockpit side for aft cabins
Safety Equipment
Anchor Equipment
The innovative Hanse 508 is the perfect yacht for relaxed blue water sailing, with its progressive design and one of the most thrilling performance levels of its class. With a fascinating interior and an exceptionally diverse range of clever customisation options. The Hanse 508 lives up to the highest standards of flexibility, style and quality of life. Let yourself be amazed by excellent luxury.
6 hull windows (3 each side)
GRP hull, isophthalic gelcoat, colour: Signal White (RAL9003), 1st layer vinyl ester resin and balsa sandwich laminat
Waterline and cove line, isophthalic gelcoat, colour: Dark Grey (RAL 7043)
+ yw disclaimer.
United Yacht Sales - Florida Treasure Coast is pleased to assist you in the purchase of this vessel. This boat is centrally listed by Sail Annapolis, Inc..
Not all boats listed online are listed with United, but we can work on your behalf. For more information on this vessel or to schedule a showing, please contact a United Yacht Sales broker by calling our main headquarters at (772) 463-3131.
Contact United Yachts to learn more!
United is the largest professional yacht brokerage firm in the world with over 200 yacht brokers in our network. By listing your boat or yacht for sale with us, all of our team are immediately notified of your boat and begin working to match your yacht with a buyer. We have many examples where boats have sold through our network and our proprietary broker forum that keeps our team connected 24/7. With hundreds of closings every year, there is no better team than United to help with the listing and sale of your vessel. Find out what your current yacht is worth on today's market!
The yacht MLS consists of thousands of available brokerage vessels from all over the world and in different conditions. Hiring an experienced yacht broker to help you find the perfect boat makes financial sense, as well as takes the stress out of the process. A United broker starts by listening to your needs, how you plan to use your boat, your potential boating locations, and your budget. We then go to work looking at all of the available yachts that fit your criteria, research their history, provide you with a clear picture of the market, and organizes the showings. We're with you every step of the way from survey to acceptance and our industry-leading support staff will make sure your closing goes smoothly.
69' Hanse 675 2018
Annapolis, Maryland, United States
Vie Le Reve
56' Hanse 575 2013
Sausalito, California, United States
53' Hanse 540e 2008
Las Playitas, Mexico
IMAGES
VIDEO